Sunday, July 23, 2017

How To Make a Water Ballon Shotgun/Cannon/CrossBow

WaterBallon Cannon made from:

2x6 lumber
 1 inch Dowels
7/64 wire
spring
3/8 inch rubber rod
 Cable ties
Grommets 

For the Smaller Version:

  • Butt Stock made from two laminated pieces of 2x6 lumber 14 inches long
  • Arms made from 2x6 lumber ripped to 2 inches and cut to 21 inches long, with a 30 degree cut on each arm
  • Need Two 3ft 3/8 rubber rods for the sling
For the Larger Version:

  • Butt Stock made from two laminated pieces of 2x6 lumber 29 inches long
  • Arms made from 2x6 lumber ripped to 2 inches and cut to 36 inces long, with a 45 degree cut on each arm
  • Need Two 5ft 3/8 rubber rods for the sling 





Thursday, June 8, 2017

How To Make A Beer Carrier DIY Six Pack

Print out the scanned template for the shape of the sides as well as marks for all the holes to be drilled. Print out should fill an entire sheet of paper from top to bottom. 



 With this template and the video below, you should be able to make your own DIY beer carrier.



How To Make A Fidget Spinner

We used the awesome woodworking website www.woodgears.ca to generate our gear template.  On the Homepage in the lower left hand corner click on the gear template generator and change the following input numbers. 

For a 2-1/2 diameter Fidget Spinner:

Tooth Spacing : 33
Gear 1 Teeth : 10
Contact Angle : 25
Click off two gears check box


For a 2-3/4 diameter Fidget Spinner

Tooth Spacing : 35
Gear 1 Teeth : 10
Contact Angle : 25
Click off two gears check box

Fidget Spinner Made from 3/8 inch Pallet Wood, Redz skateboard bearing, 5/16 inch steel bearing balls, and a 1/4 inch dowel pin.

With the gear input information and the link to the video you can make your own fidget spinner




How To Make DIY Letter Stencils for Your Router : Sign Making

These are the Dimensions I used for all my letter patterns.  Obviously the width of each letter with vary depending on  the letter and whether or not it is Capitalized, but if you kept a consistent 1/8 spacer on the side of either letter your alignment will be fine.  I mounted all my letters 1inch from the base of the pattern.

Specifications for this project:

- Font- HighTower Text
- PT - 400
- 5/16 - Bushing
- 1/8 inch Spiral Cutting Bit
- !/8 spacing on either side of the letters on the pattern
- Pattern material at least 1/4 inch thick
- Pattern material 6 inches tall

With these measurements and the video below you can make your own letter stencils and signs

Stencil Making Video

How To Make A TV Stand Cabinet Out Of Old Doors




The first door I started off with was 78- 1/4 x 29 15/16.  
The second door 78-1/4 x 29-15/16

*Keep In Mind* All my measurements are based on that door size.  Finding an old door exactly the same as mine might not be super easy, but you can adjust all the measurements and cuts to work with your size door.  A general  rule of thumb is reclaimed materials will not always be square/true, so use all these measurements as a rough guide not a hard fact.  What you are working with will be different then what I worked with.  Contact us on our Youtube https://www.youtube.com/channel/UCqKCuJ4_6T4H_3ZOPSPANHg page with questions.  Using this blog and our accompanying Youtube videos of the build process shows all the steps.








 

Monday, January 26, 2015

How A HoneyBadger Makes Crown Molding 




 Starting point was a piece of reclaimed floor board pine.



 Reclaimed floor board pine


Ripped down the pine to thickness as well as saved the hassle of removing many layers of old paint.



Rough marks of where I wanted to cut my coves to match the original molding



Dry fitting the piece on the table saw. You can cut coves in lumber by running wood at an angle across your saw blade gradually to remove minimal thicknesses of lumber at a time til you get the depth you desire


Close up of my homemade cove cutting jig with lumber in place


Jig without lumber in place


First pass through the jig


First Cove starting to form


Close up of finished first cove


First Cove 


First Cove - Side View 


My second cove needed to be much narrower so the jig was adjusted to accommodate that cut


Jig in place


First run through jig


Close up of both roughed out coves


Finished crown molding after final touches and sanding



Thursday, November 20, 2014


54 degrees in the shop today 


Turning an old chair back into a wall mounted shelf 


The most tedious part was figuring out the right angle to mount the shelf and added wooden brackets.  Since this is an old chair back it does not sit against the wall at perfect 90 degrees so I had to dry mount a shelf to the chair and keep checking the angle against a wall to get it right.


In order to securely mount a shelf to the chair I made two custom oak brackets with notches cut out for the shelf angle and to attach it to the chair.  I matched some of the preexisting curves of the chair in making the bracket so it did not look overly clunky on the finished piece. 


Inside view of the bracket with notches for mounting 


Finished bracket 


Bracket secured to the chair with screws to be later filled with oak dowels.


Drawing out the shelf curve on a piece of reclaimed walnut 


Bracket attached to the chair 


Dry fit of shelf 


Walnut shelf secured to the chair and wooden brackets 



Finished product in the store.